ASTM C582 PDF
ASTM C + REDLINE: STANDARD SPECIFICATION FOR CONTACT- MOLDED REINFORCED THERMOSETTING PLASTIC (RTP) LAMINATES FOR. Start. Standard ASTM standard · ASTM C latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products (ASTM VOL ) . C – 95 – This document is not an ASTM standard and is intended only to provide the user of an.
|Published (Last):||2 December 2014|
|PDF File Size:||3.60 Mb|
|ePub File Size:||7.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
A thixotropic agent may be added to the resin for viscosity control. Gaps are not permitted.
Additional desirable considerations in choosing a veil for a speci? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? No plies may be omitted. Your comments are invited either for astn of this standard or for additional standards and should be aetm to ASTM International Headquarters.
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Workmanship and Finish 9. When such items are required, limits for each shall be agreed upon between the fabricator and the buyer. The resin matrix is applied by various methods, including brush, roller, or spray gun. Parte 1 de 2 Standard Specification for Contact-Molded Reinforced Thermosetting Plastic RTP Laminates for Corrosion-Resistant Equipment1 This standard is issued under the fixed designation C ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.
Consolidation of the composite laminate is by rolling. Tensile strength, ultimate—17 psi MPa. D Corrosion barrier Plies 1, 2, and 3 shall gel before structural plies are added.
ASTM Volume No plies may be omitted. The resin matrix is ast by various methods, including brush, roller, or spray gun. The abbreviation for reinforced thermoset plastic is RTP. See Table 1 and Table 2 for standard thicknesses.
Astm c – astm normas fibra de vidrio
NOTE 11—Thicker laminates shall not be used for such tests, as results will vary signi? C Corrosion barrier Plies 1, 2, and 3 shall gel before structural plies asstm added. A thixotropic agent may be added to the resin for viscosity control.
C Cut edges must be covered with resin.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. NOTE 1—The laminates covered by this specification are manufactured during fabrication of contact-molded RTP tanks, piping, and other equipment. Link to Active This link will always route to the current Active version of the standard.
Location of exotherm plies may be shifted within the laminate body. As an alternative, a minimum astk two passes of chopped roving minimum? A superscript epsilon e indicates an editorial change since the last revision or reapproval.
C Corrosion barrier Plies 1, 2, and 3 shall gel before structural plies are added. D Test Method D ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Flexural strength, ultimate—22 psi MPa. Tensile strength, ultimate—17 psi MPa. Interpretation of mechanical property data obtained from such specimens is discussed in Appendix X1.
NOTE 7—Table 1 and Table 2 are for reference purposes sstm do not preclude other laminate-type constructions, such as nonwoven biaxial or unidirectional fabric, which may be agreed upon between the buyer and the seller, or may be added to this speci?
ASTM C582 – 09(2016)
Location of exotherm plies may be shifted within the laminate body. C — Historical Version s – view previous versions of standard. Test Method D Astm a Astm a NOTE 1—The laminates covered by this speci? The abbreviation for reinforced thermoset plastic is RTP.
It is the responsibility of the user of c82 standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified thermosetting resin laminates comprising the materials of construction for RTP corrosion-resistant tanks, piping, d582 equipment. This specification is limited to fabrication by contact molding.