CMU200 MANUAL PDF
R&S®CMU Universal Radio Communication Tester For more general information about the R&S®CMU, refer to the product . in manual mode. throughout this manual, CMU and CMU is generally used as an abbreviation for the Universal Radio Communication. Testers R&S CMU and R&S. note that not all GSM options described in this manual are supported. The different R&S CMU models are also described in the product brochures. The high.
|Published (Last):||3 April 2006|
|PDF File Size:||14.13 Mb|
|ePub File Size:||10.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
These combinations of options can be installed together and will be simply referred to as “options” through the remainder of this section. From the start mode, it can be switched to either insert or overwrite mode.
The supplementary options must be enabled with a key code but can not be deactivated. More refinements More refinements Audio Audio generator and analyzer including multitone measurements, see below in this Chapter It is a versatile measuring instrument for a large variety of digital and analog network tests all of them are optional, see separate manuals.
Chapter 2 provides an introduction to the operation of the CMU by means of typical examples of configuration and measurement; for a description of the operating concept refer to chapter 3. Popup menus which configure a measurement are activated by pressing the calling softkey main softkey in the measurement menu twice selection of softkey and subsequent opening of popup menu.
Pull-down lists are marked by an arrow and select one out of n settings.
The Application field indicates whether the serial port is used as a printer connector Printer, if COM 1 was selected as printer port in the Print tab; see p. Select the card in slot 0 or slot 1 as cm2u00 installation medium.
Do not cover the lateral and rear ventilation holes. Measurement menus Power cmu2200 Spectrum: The auxiliary editor is used to edit a name that may extend over several lines.
Pull-down list fields are similar to the list fields described above as far as their function and operation is concerned; however, they are compressed into one line in the popup menu.
The steps to perform are explained on the left side of each double-page together with the results obtained on the CMU screen. Signalling does not necessarily have to be activated by means of a cmu2000 menu; for example, the Power menu for GSM mobile tests can be called up immediately, without transferring any signalling information.
Dhameliya Harkishan 20 November at Basic settings are discussed manusl section Measurement Control on page 3. Auto Automatic setting of maximum input level autoranging according to the power of the applied signal.
Installed hardware and software options and equipment Options. A copied file can be stored several times to different directories and storage devices. In contrast to other instrument settings, the repetition modes in manual and remote control are independent and do not overwrite each other. Select fields and tables in manhal popup menus can be controlled intuitively using the cursor keys types. In the insert mode, the cursor appears in the input field. After terminating the startup procedure, the instrument changes to the last main menu or graphical measurement menu of the previous session.
The new features described in this manual are listed below. The default setting is Off. Vmu200 the same Chapter you can find a short tutorial on the entry of numbers and characters.
We also point out alternative settings and related measurements which could not be reported in detail. Basic elements Flexibility and uniformity Controls The CMU is operated under menu control via keys, softkeys and hotkeys: With the default setting Free Run the measurement is not synchronized to the frequency of the incoming pulses: The Mcu200 provides selectable and non-selectable softkeys.
The definition of an evaluation period changes from one measurement to another: Back to previous manaul Close the current screen and go back to the main screen. The screen is dimmed around the edge presumably from curling of reflector around fluro tube. For operation of list fields cmu2200 Table Tested to power on display is shown. In remote control, the band pass for AC and DC coupling is selected with different commands, e. Thank you for checking out our listing.
Ediseja 21 CMU 200 User Manual Page 28
The following selection dialog is automatically skipped. Select the associated softkey to activate the select field and expand the list. The mains switch can be set to two positions: Modified Item see all. Deleting the non volatile ram can be useful after an abnormal termination of a CMU measurement session.
Rohde & Schwarz R&s CMU200 Universal Radio Communication Tester GSM GPRS WCDMA
Control softkey always at the top right is available in all measurement menus. The Input Level softkey configures the input level, the power range and manuql attenuation factor.
See the relevant manuals for more information.