COINCO GLOBAL 2 PDF

0 Comments

Coin Acceptors (Coinco) is a world leader in the design and manufacture of coin mechanisms, bill acceptors, control systems, and vending machines for the. Vantage · BillPro · Bill Recyclers (1/0). Vantage VR6 · Product History (2/0). Bill Acceptors · Coin Changers · iris (2/2). iris Reader · iris Media · Coinco-Office (0/1) . COINCO GLOBAL 2® SERIES O P E R AT I O N AN D S E R V I CE MANUAL TABLE OF CONTENTS SECTION 1: GENERAL INFORMATION.

Author: Sarr Mezikus
Country: Peru
Language: English (Spanish)
Genre: Software
Published (Last): 25 June 2016
Pages: 317
PDF File Size: 7.75 Mb
ePub File Size: 2.76 Mb
ISBN: 857-7-32911-858-2
Downloads: 96738
Price: Free* [*Free Regsitration Required]
Uploader: Bragore

Repeat the above steps until the remaining three price lines have been assigned a vend price. You will exit the Display Mode if one of the following procedures is performed: Float Mode is used to systematically reduce the number of coins kept in a tube.

Acceptor is dirty or foreign matter in coin accept path Check to see that acceptor coin path is clean and free of matter Clean acceptor and remove any foreign matter.

To clean the coin ramp, lift the acceptor gate upward and diagonally to coincl right. Four slots have been placed in the front of the changer along the pay-out assembly clinco to assist in this procedure. Remove power from the vending machine. Press C again to return to the Address Display. For normal environments, cleaning glbal recommended every six months.

The far right decimal point will illuminate indicated the selection has been stored. After setting the vend price and the desired options, press and release the Mode Button to store the new setting. Press Button C again to store the selection. Once all four prices have been set, press A twice to exit the Display Mode. No Inventory Buttons are pressed or coins are dropped for more than 45 seconds; 2.

  ANATOMIA DUSZY CAROLINE MYSS PDF

Place a screw driver into the slot and apply an inward pressure to free the tube retainer tab whilst pulling upwards on the tube. Refer to Section 3: Due to its small size, it can be easily misplaced. ON Operates as a Four-Price changer.

Coinco global 2 mdb/other – Global 2 – VendingOutlet Private Webshop

Once the tube reaches its float level in Standard Float Mode, any coins normally routed to that tube will be sent to the cashbox. Figure 1 Series Figure 2 5. Use either Inventory Buttons B or D to increase or decrease the address values as needed.

See vending machine manual for details. Press A to exit the Foinco Mode. Example of setting up user defined coin routing. If the first, fourth and fifth price setting switches are in the UP position, the vend price setting would be 25 x 1 or 25 assuming the lowest denomination coin accepted is 1. The vend price must be set to an amount greater than zero for the changer to accept coins in single-price mode.

Installation and removal can stress the plastic, causing the shims to lose their ability to stay firmly in place. Press C to enter.

4 Coinco Global 2 Coin Mechanisms GBP G 801 MDB Plus

When the light is OFF, all enabled coins in the coin set are accepted. Remove any lodged coins. Figure 8 for 4-Price Electromechanical 7. If LED is on, replace acceptor.

  HISTORIA DE LAS IDEAS PEDAGOGICAS MOACIR GADOTTI DESCARGAR PDF

Coinco Global 2

Press B increase or D decrease to choose one of the programmable payout configuration selections. Float modes will be turned off and coin counts will be cleared for any tube in which all coins assigned to the tube were not previously assigned to the tube and have been assigned during the current payout configuration session. Key reader, Bill validator, Audit device etc. Set the desired vend price and options on the changer.

Use button B increase or button D decrease to lgobal the correct value. gobal

The far left digit represents tube A through the far right digit representing tube D. Supply Voltage Error The error codes listed below are displayed upon occurrence: Push snap toward top of housing and remove upper tube sense board which will separate from main logic board upon removal.

Information currently stored in non-volatile memory will be displayed with the far right decimal point illuminated. Replace the acceptor by inserting bottom acceptor studs into changer housing guides. If coin still goes to cashbox, replace acceptor with good acceptor and test to see if changer functions properly.

Programmable tube floats allow variable tube level adjustment.

Press C again to view the lower four digits, including the decimal point if any.