LM741CH DATASHEET PDF
LMCH Datasheet, LMCH National Semiconductor Operational Amplifier Datasheet, buy LMCH. LMAH/ or LMCH. See NS Package Number H08C. Dual-In-Line or S.O. Package. DS Order Number LMJ, LMJ/, LMCN. LMCH LM – Operational Amplifier, Package: TO-5, Pin Nb=8. The LM series are general purpose operational amplifiers which feature improved.
| Author: | Zulkisho Mazubar |
| Country: | Bermuda |
| Language: | English (Spanish) |
| Genre: | Literature |
| Published (Last): | 17 August 2015 |
| Pages: | 17 |
| PDF File Size: | 17.26 Mb |
| ePub File Size: | 4.86 Mb |
| ISBN: | 522-3-36347-372-8 |
| Downloads: | 66586 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Akikasa |
Posted by moohoo in forum: You May Also Like: Also, a 40KHz input frequency did not result in a Triangle Wave output- as can be seen in the attachment. The output signal should resemble a triangle wave.
LMCH Datasheet(PDF) – National Semiconductor (TI)
S- I will also try conencting the Amplifier in Inverting and Non Inverting mode, to see which results issue forth. Yes, my password is: Datashet am at my wit’s end, and I was wondering weather anyone on this fantastic Electronics Resource might be able to help me work out where I am going wrong.
The attachment contains an image of the circuit and waveform for the calculation above. Thus the Slew Rate can be calculated thus: This is being facilitated through the use of Multism v11, in which I have constructed a Unity Gain circuit with an LMCH, which is the Op-Amp that I wish to focus on for the purposes of this question.
I gave those values from the lab below. Oct 23, 5. The input signal is a 2V square wave. Oct 24, 7.
No, create an account now. Make your circuit with a 1k resistor as the Ri and a 10k resistor as the Rf and set the signal source to 40 kHz 2 V pk to pk.
Operational Amplifier
Your name or email address: A Triangle Wave is output when the frequency passes 1MHz, however this attenuates the Output Voltage as the Amplifier struggles to react to the changing square wave input. I have tried to make Slew Rate calculations based off the signal displayed by the Multisim virtual oscilliscope, at many different input frequencies 10Hz to 10MHzbut I seem to be getting the wrong answer consistently.
Oct 22, 2. Jul 17, 4 0. Didn’t your school give you a specific lab to do with known components? Anyway, thanks for the help thus far- any further thoughts that anyone may have regarding this problem would be greatly appreciated. Find out how Levi’s Stadium is setting a new standard for how we experience football.
Quote of the day. Can an op-amp with high slew rate replace an op-amp with low slew rate in a partic Dattasheet by kling in forum: Observing the Output Square Wave, some Slewing is clearly evident.
I am assuming that this reading can be obtained without placing a particular kind of load at the Op-Amp’s output, as the Datashheet does not specify one.
Oct 23, 3.
Problem with measuring the Slew Rate of an LMCH Op-Amp on Multisim | All About Circuits
You will see appoximately 0. Apr 26, 3, 1, Dec 20, 10, 1, Looking forward to hearing some suggestions. Slew rate of op-amp Posted by jegues in forum: The assignment simply states: Placing Rin and Rf in the circuit did improve the results, thus I can try altering the ratio between the two to obtain a good slew rate value- however, if the Datasheet specifies 0. Oct 22, 1.
